Home / Quality & QC

Rigorous Quality Assurance & Metallurgical QC Testing in Jamshedpur

Upholding our uncompromising zero-defect engineering commitment at our Adityapur plant. We combine computerized chemical analysis, mechanical testing, and 100% heat traceability.

100% Heat
Traceability Guaranteed
28-Channel
Optical Spectrometer
MTC Level 3.1
EN 10204 Test Reports
> 90%
SG Iron Nodularity Guarantee
science In-House Metallurgical Laboratory

Optical Emission Spectrometer & Chemical Validation

Chemical consistency is the cornerstone of ductile and grey iron performance. Our computerized optical emission spectrometer analyzes 28 chemical elements simultaneously within 60 seconds from chilled coin samples taken directly from the furnace bath and pouring ladle.

Pre-Pour Melt Calibration:

Carbon (C), Silicon (Si), Manganese (Mn), Phosphorus (P), and Sulfur (S) checked and adjusted before magnesium spheroidization.

Magnesium Recovery & Nodularity Verification:

Residual active magnesium maintained between 0.038% and 0.052% to guarantee over 90% spheroidal graphite count per ASTM E2568.

Trace Element Suppression:

Strict ppm control over anti-nodulizing elements like Lead (Pb), Bismuth (Bi), Antimony (Sb), and Titanium (Ti).

Optical Emission Spectrometer Lab at Tatanagar Foundry Jamshedpur
Spectroscopy Bay
28-Channel Optical Emission Spectrometer Laboratory
Mechanical & Non-Destructive Testing

Complete Physical, Strength & NDT Validation

Ensuring 100% compliance with ASTM, IS, DIN, and OEM customer drawing tolerances.

fitness_center

Universal Tensile Testing (UTM 60T)

Standard Y-block and keeled test coupons pulled on our computerized 60-Ton UTM, generating precise stress-strain curves, proof yield strength, and percentage elongation.

diamond

Brinell & Rockwell Hardness Testers

Equipped with 3,000 kgf Brinell testers (10mm ball indenter) for heavy castings and Rockwell C-scale testers for induction hardened wear components.

biotech

Microstructure & Image Analysis

High-resolution inverted metallurgical microscope with computerized image analyzer measuring graphite nodule count (per mm²), nodularity percentage, and ferrite/pearlite ratio.

track_changes

Magnetic Particle Inspection (MPI)

Fluorescent wet magnetic particle inspection detecting subtle sub-surface hot tears, shrinkage fissures, and micro-cracks in critical safety railway and steering components.

sensors

Ultrasonic Velocity Testing (UT)

Non-destructive ultrasonic pulse velocity measurements providing instantaneous, 100% in-line verification of SG iron nodularity on finished commercial vehicle parts.

water

Hydrostatic Pressure Testing Bay

High-pressure hydrostatic testing up to 100 bar with calibrated digital pressure loggers for valve bodies, pump volutes, and high-pressure fluid casings.

Traceable QA Protocol

6-Stage Quality Assurance Flowchart

Guaranteed heat-wise traceability from raw scrap charging to final dispatch inspection.

01

Raw Material Inward QC

Chemical analysis of virgin pig iron, steel scrap, ferro-silicon (FeSi), and FeSiMg nodulizers before charging.

02

Pre-Pour Optical Spectro

Bath thermal and chemical verification. Heat released for tapping only after 28 elements match spec sheet.

03

Moulding Sand Quality

Hourly testing of green sand moisture, permeability, active clay, and compressive strength on DISA line.

04

Test Coupon Mechanicals

Tensile, elongation, yield, and microstructural nodularity validated on Y-blocks poured with each heat batch.

05

100% Visual & NDT Scan

Shot-blasted components examined under UV magnetic particle inspection and ultrasonic nodularity scanning.

06

CMM Dimensional & MTC 3.1

Coordinate Measuring Machine dimensional audit, anti-rust primer application, and issuance of EN 10204 3.1 test report.